Kontakt

Za Vas smo dostupni od ponedeljka do petka od 8:00 do 17:00 časova. Preko ovog linka možete pronaći kontakt osobe za Vaš region.

Sedište u Wolfurtu
+43 5574 6706-0

Vaše kontakt osobe

Korpa {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Artikal   Izmena pregleda korpe

Primedba

Slika Artikal kom. Cena za jedan komad Ukupna cena Ukupna cena uklj. popust
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

:  Prijavite se da biste videli svoje cene i nastavili da naručujete.

Lowering tension

In our selected range you can find the right material for virtually any application.

M W10PM powder metallurgical steel

DESIGNATION:

EN: HS 10-2-5-8

INDICATORY ANALYSIS:

C1.6
Cr4.8
Mo2.0
V5.0
W10.5
Co8.0

Strength:

max. 285 HB
(≈ max. 970 N/mm²)

THERMAL CONDUCTIVITY AT 100°C:

26 W/m K


CHARACTER:

High-speed steel produced by powder metallurgy with highest compressivestrength, high adhesive wear resistance and excellent toughness, very high workinghardness possible

APPLICATION:

Blocks for eroding, dies, cutting punches and cutting tools for extremely highrequirements, fine blanking punches, embossing tools, cold solid forming


TREATMENT BY:

Polishing:
best metallurgical properties for mirror finish

Nitriding:
highly suited for nitriding

EDM:
highly suited

Coating:
highly suited


HEAT TREATMENT:

Soft annealing:
870 to 900°C for about 2 to 5 hours
slow controlled cooling inside the furnace 10 to 12°C per hour to about 550°C,
further cooling in air, max. 300 HB

Hardening:
curing temperature: see tempering chart
quenching in oil/compressed gas/air/hot bath
obtainable hardness: 68 HRC

Tempering:
slow heating to tempering temperature (in order to avoid formation of cracks)
immediately after hardening;
keep at tempering temperature for at least 1 hour
four tempering cycles are recommended, with cooling to room temperature in
between


TEMPERING CHART:


TECHNICAL TIP:
  • Retains hardness at high temperatures due to highcobalt content
  • Excellent for PVD and CVD coating without risk ofdimensional changes, as the steel is tempered atmore than 520°C

To the mould making overview To the die making overview

Available in the web shop as:
Data sheet M W10 PM

Otvori PDF

Material grades brochure

Material grades brochure

Material grades poster

Material grades poster

Pošlji

Da li imate otvoren nalog?

Ukoliko imate pristupne podatke za Meusburger portal, prijavite se ovde:

Izgubljena lozinka?

Novogenerisana lozinka je poslata i trebalo bi uskoro da se pojavi u vašem prijemnom sandučetu. Želimo vam uspešan dan.

Unesite Vašu e-mail adresu.
Poslaćemo Vam novu lozinku.

Izaberite zemlju

Lokacije

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version